In this article below you can discover a bunch of outstanding resources when it comes to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Installing a bathtub isn't exactly rocket science, but it does call for strong plumbing, woodworking, as well as often, tiling skills. Changing an old bathtub with a new one is additionally a moderately hard project. If the old tub is easily easily accessible, the task can move rapidly; if you need to open a wall to remove the old bathtub as well as position the new tub, the job is a lot harder. In either situation, the task is within a residence handyman's skills, although you will need a helper to vacate the old tub and embeded in the brand-new one. See to it you have certified yourself for the task and are comfortable trying it. Instead of working with a service provider to take over a halfway-completed job, it is much better to consider using one prior to you start. Opportunities are you may require a specialist plumber to make tube links.
This write-up will certainly assist you set up a brand-new tub in your washroom if you have actually currently gotten a brand-new tub and also do not require to alter the plan of your previous water pipelines.
Your tools and material list need to make up the following:
Preparing for the Installment
First of all, the supporting framework supplied with the bathroom must be fitted (if required) according to the supplier's directions. Next off, fit the taps or mixer to the bath tub. When suitable the tap block, it is important to make certain that if the faucet comes with a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the faucets unit to avoid pressure on the bath tub.
Fit the flexible tap connectors to the bottom of the two taps utilizing 2 nuts as well as olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet through the hole in the bathroom. Make use of the nut provided by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. See to it you make use of every one of the provided washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom should now be ready to be fitted in its final setting.
Removing Old Touches
If you require to replace old taps with new ones as a part of your installation, after that the first thing you should do is detach the water supply. After doing so, switch on the taps to drain pipes any kind of water continuing to be in the system. The process of eliminating the existing faucets can be quite problematic because of the limited accessibility that is usually the case.
Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipes to the taps. Have a fabric prepared for the remaining water that will originate from the pipelines. As soon as the supply pipelines have been gotten rid of, make use of the very same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the solitary faucets from transforming throughout this procedure. When the faucets have been eliminated, the holes in the bath/basin will have to be cleansed of any type of old sealing substance.
Before proceeding to fit the brand-new faucets, contrast the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.
Installing the Tub
Utilizing both wooden boards under its feet, put the tub in the needed placement. The wood boards are useful in uniformly spreading out the weight of the bath tub over the location of the boards rather than concentrating all the weight onto 4 small points.
The next objective is to make sure that the bath tub is leveled all round. This can be attained by inspecting the spirit level as well as changing the feet on the bathtub till the spirit level checks out level.
To set up faucets, fit the bottom of the furthest versatile tap port to the proper supply pipe by making a compression join; after that do the exact same for the other faucet.
Switch on the water and also check all joints and brand-new pipework for leaks as well as tighten them if essential. Fill the tub as well as additionally check the overflow outlet and also the typical outlet for leakages.
Finally, take care of the bathroom paneling as explained in the producer's instruction manual. Tiling as well as sealing around the bathtub ought to wait until the tub has been used at the very least once as this will settle it into its final placement.
Suitable New Taps
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic adapter to prevent damages to the thread. One end of the port fits on the plastic tail of the tap and the various other end offers a link to the existing supply pipes.
If you need to fit a monobloc, then you will call for decreasing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the mounting opening in the bath/basin making certain that the washing machines remain in location in between the faucet and the sink. Secure the tap in place with the maker supplied backnut. As soon as the faucet is safely in place, the supply pipes can be connected to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with normal faucet adapters. The previous type must be linked to the tap ends initially, tightening up just by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the area where the bath satisfies the tile, it is necessary to seal the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to break a stiff seal, causing the water to permeate the wall surface in between the bath as well as the tiling, leading to difficulties with moisture and possible leakages to the ceiling listed below.
You can pick from a selection of coloured sealants to blend in your fixtures and fittings. They are sold in tubes and cartridges, and can securing voids approximately a size of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of soaked newspaper or soft rope. Remember to constantly fill up the tub with water before securing, to enable the movement experienced when the bathtub is in use. The sealer can break relatively early if you do not consider this activity before securing.
Additionally, ceramic coving or quadrant tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are likewise easily available on the marketplace. It is advisable to fit the floor tiles utilizing water-resistant or water-proof sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I came across that blog posting about How to Install a Bathtub Yourself when perusing the search engines. Do you know somebody else who is occupied with the topic? Why not promote it. I praise you for your time. Kindly visit our website back soon.
Stop the flood! Call.